© 1998-2011 by Magenta Research, LTD., All rights reserved. Magenta Research, LTD, 128 Litchfield Road New Milford, CT 06776 USA
USA: (800) 805-0944 INT: (+1) 860-210-0546 www.magenta-research.com
Document # 5310272-01 Rev-01 (11/8/2011) Page 1 of 3
MultiView II T4 Transmitter:
Quick Start Guide
The Magenta MultiView™ II T4 transmitter extends an analog video signal over standard CAT5 cable (also
CAT5e and CAT6), provided over 4 link outputs. There are user-configurable settings for video, audio, and serial
options which can be controlled from the front panel. For more details please refer to the complete MultiView™ II
T4 User Guide, available for download at
www.magenta-research.com, or scan the QR-code shown here to access the
user guide directly:
Required Tools / Hardware / Materials: Tools include a
ppropriate screwdriver(s) and mounting hardware
(optional, for example: rack-mount, wall or under-desk mounting). Required materials include appropriate cables for your specific
application.
Power-up Check:
After all signal and power cables are connected, then apply AC power. The power-on indicator should light. If the
video source is providing a valid VGA (RGB+HV) video signal, the video-status indicator should also be on (for any other type of video
signal this status indicator will always be off). If there is a local monitor attached, a video image should appear on the monitor. If there is
no image on the display, recheck all cables and ensure the display is turned on.
Front Panel Controls: (
Refer to Figure-2) There are two buttons (COPY/CFG and DDC MODE/SEL), and several green LED status
indicators. These are used to control the operating modes of the transmitter, and to display current status. In “normal-mode”, the CFG
indicator is off. In “configuration-mode”, the CFG indicator is on or flashing.
DDC Mode Selection:
When the T4 transmitter is operating in normal-mode (CFG indicator is off), it is possible to quickly select
between the 3 DDC operating modes simply by using the DDC MODE button at any time:
STD: Selects the Magenta Magic DDC profile. Press the DDC MODE button until the STD indicator (LED 6) is on. The
Magenta Magic profile is a default set of common video resolutions. This is the factory default setting.
LOCAL: Selects the DDC profile from a locally-connected display. Press the DDC MODE button until the LOCAL
indicator (LED 7) is on. The LOCAL mode allows the video source device to directly read the DDC profile from the locally
connected-display (if present). Note that LOCAL mode does not store any DDC profile information inside the T4 device.
COPY: Selects a previously stored copy of a DDC profile. Press the DDC MODE button until the COPY indicator (LED8) is
on. To use the COPY mode, a DDC profile must have already been read and stored into the T4.
To perform a DDC-copy operation: Ensure the COPY mode is selected (LED8=on), then: 1) Connect a display to the
LOCAL OUT port. (2) Push and hold the COPY button until the copy-status indicator flashes 3 times, indicating a successful
operation. If it only flashes once, the operation failed and the previously stored DDC profile (if any) will remain unchanged.
Figure 1 – T4 Transmitter
Rear View
(Optional) Depending on installation requirements: At any
time during installation, the transmitter may be securely
mounted using appropriate brackets and hardware.
PRECAUTIONS: (1) Do not apply AC power until instructed to
do so. (2) This equipment is not intended for, nor does it
support, distribution through an Ethernet network. Do not
connect these devices to any sort of networking or
telecommunications equipment! (3) Use only Magenta
Research LTD approved MultiView™ II power adapters. Failure
to do so may damage this device and will void the warranty.
Figure 2 – T4 Transmitter
Front View
Connect up to 4
CAT5 cables via the
LINK OUT ports.
Connect video source to
the transmitter’s VGA IN
port.
(Optional) Make serial or
audio connections via the
AUX I/O (in & out)
connectors, as needed.
Connect the DC power
cable (+5VDC @ 3A. max)
to the POWER port.
Power-on indicator
Video-status and
DDC-copy indicator
(Optional) Connect
local display via the
LOCAL OUT port.
Operating mode:
Off = normal, On = Config
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels